1-Rollers / Products
Standard Radial Force Sensor.
By the small design and high measurement precision it can optimally be used for most of all applications. Suitable for tensile force measuring of threads, monofilaments, wires, cables and similar material. Equipped with a cylindrical measuring roller also tapes, ribbons and foils up to
250 mm width can be measured.
Nominal loads:
20cN to 5000N
Measuring ranges:
from
High > 10 fold overload protection
Analog output signal 0 - 10V
option 4-20mA
Protection class IP 50
(IP 64 possible)
Housing is available with thraed M25x1,5mm and two nuts
Acid proof design available
Available accessories:
- standard guiding roller
- custom made roller
- fastening device
Data sheet:
cylinders up to a width of 250 mm. So the tensile forces can be
measured. The measurement is independent of lever arm. For installing in machines.
Measuring widths:
According to your requirements
Maximum measuring width:
250 mm
Housing is available with thraed M25x1,5mm and two nuts
Data sheet:
Nominal loads:
50N to 1000N
Measuring ranges:
from 1N to 10kN
Analog output signal 0-10 V
Available accessories:
- standard guiding roller
- custom made roller
Data sheet:
Equipped with a cylindrical measuring roller also tapes, ribbons and foils up to 100 mm width can be measured.
Nominal loads:
2N, 3N, 5N, 10N, 20N,
30N, 40N, 50N
Measuring ranges:
from 10cN - 500N
Protection class: IP 50
Light aluminium housing
Available with built-in measuring amplifier
Data sheet:
Radial force sensor of miniature design.
Externally measuring amplifier required.
The measuring axle is designed for rolling bearings with bore of 20mm/25mm dia.
Externally measuring amplifier required.
Nominal loads:
200N to 3000N
Protection class: IP 65
Housing made from stainless steel
Available accessories:
- Standard guiding roller
- Custom made roller
Data sheet:
Type M1191 XY is a radial force sensor with strain gage full-bridge, for the measurement of forces from two 90 ° direction offsets without amplifier. To transform the low measuring-voltage into a normal signal, it needs an external amplifier.
Therefore Tensometric amplifier are suited:
2KMV 10, MV 110 ( without display )
SA 2xDMS 610 ( with display )
Application: Tensile force measurement on X and Y direction
Nominal loads: 30 N, 40 N, 50 N, 100 N, 200 N others upon request
Overload-protection: > 4 to 8 times of nominal load
Protection: IP 52, Option IP 64
Material: (tube) housing and shaft : stainless steel Sealing material: Silicon, SL 601
Housing is available with thraed and two nuts
Accessories available: Connection cable, amplifier with or without display
measuring roller, clamping device Z 1391
Data sheet M1191XY:
Radial - Force - Sensors out of series M 1100 - 20 and M 1300 - 20 are precise and reliable measuring-systems,
as well high overload-protected as high in long-time-stability.
For measuring tensile forces on running material, fit a ball-bearing mounted roller on the journal-bearing. This measuring-roller has to be mounted in a position, that the material which is measured, will deviated in a defined angle. Here angle of contacts, of the material which is measured - around the measuring roller -, between 3° and 180° are possible.
The resulting radial forces, due to the deviation, are measured by the sensor. The radial force is proportional to the tensile force, in the material which is measured. Corresponding to this radial-force, the nominal load of the sensor is to select.
Application Tensile force measurement on : cables, wires, ropes, rubber-cables, copper-cables, etc.
Sensor for using in Tensometric measuring-stations.
Nominal loads: 30 N, 50 N, 100 N, 200 N, 300 N, or 400 N others on request
Measuring range: By changing the angle of contact - around the measuring-roller -, the measuring range is variable.
Series M 1300 - 20 Strain-gage, full-bridge, with built-in amplifier. The sensor transforms the, on the measuring-roller, active radial force into a proportional electric outputsignal of 0 V up to +10 V .
Adjusting screws for the electrical zero ( Offset ) and for the calibration ( gain ), are accessible from outside, at the connection-cable-page by means of a screw-driver. Connection via 5-pol. male connector.
Accessories available connection-cable, amplifier with or without indication the tensile-forces, rollers.
Data sheet M1300-20:
It is easy to fix it in its place of measurement, and it is ready for operation immediately. Fixing the sensor is optional, several sensors can be grouped in one block.
Measuring ranges:
STAK 1390:
0-2N, 0-3N, 0-4N, 0-5N, 0-6N,
0-10N, 0-20N, 0-30N
STAK 1390-C:
0-30N, 0-50N, 0-100N, 0-200N,
0-300N, 0-400N, 0-500N
With built-in measuring amplifier. zero point setting (taring)
and amplification (calibration).
Analog output signal: 0 - 10 V
Datasheet Stak1390:
Type STAK 1390 is a compact, precise and reliable meas uring head for compression and tensile forces. It contains all necessary components for measuremen t in a very flat housing.
- Measuring system
- Amplifier with analogue output
- Adjustment for zero ( tare )
- Adjustment for amplifying ( calibration )
This series M 1111 is a novel-type for precise measurement of radial-forces and tensile-forces on running material. The radial-force measuring - system is space-saving accommodated inside of the anti-friction-bearing. On the outer ring of the anti-friction-bearing a corresponding roller will be mounted. For measuring tensile forces, the sensor has to be mounted in such a position, that the material - which should be measured - will deviated in a defined angle.
Data sheet M1111:
Type M 1191 - C is a radial-force sensor without amplifier. For transformation the low measuring-voltage into a norm-signal, it needs an external amplifier.
Data sheet M1191-C:
Type M 1191 KA is a radial force sensor without amplifier. For transformation the low measuring- voltage into a norm-signal, it needs an external amplifier.
Type M 1191 KAS is a radial force sensor without amplifier. For transformation the low measuring voltage into a norm signal, it needs an external amplifier.
Housing is available with thraed and two nuts
Data sheet M-1191-KAS:
Type M 1192 KA is a radial-force sensor without amplifier. For transformation the low measuring-voltage into a norm-signal, it needs an external amplifier.
Type M 1391 is with built-in amplifier. It supplies an output signal of 0 to +10V, correspon ding to 0-100% the nominal load. To adjust the electrical zero and the gain (calibration), the corresponding potentiometer are accessible from outside.
Type M 1391-HA is with built-in amplifier. It supplies an output signal of 0 to +10V, correspon ding to 0-100% off the nominal load. The adjustment off electrical zero and the gain (calibration) is made by Tensometric.
Data sheet M1391-HA:
Content
Datenblatt:
(only available in german language)
Type M 1392 is with built-in amplifier. It supplies an output signal of 0 to +10V, corresponding to 0-100% the nominal load. To adjust the electrical zero and the gain (calibra tion), the corresponding potentiometer (7) are acce ssible from outside.
Content
Type M 1392-L is with built-in amplifier. It supplies an output signal of 0 to +10V, corresponding to 0-100% the nominal load. To adjust the electrical zero and the gain (calibration), the corresponding potentiometer are accessible from outside.
